Bildirimlerim
DIY & Crafts

Simple Floating Nightstands You Can Build Quickly

This straightforward, step-by-step instruction set lets you construct simple DIY floating nightstands. These pieces help maximize floor area in a compact bedroom while…

Simple Floating Nightstands You Can Build Quickly

Learn how to craft these simple DIY floating bedside tables with our easy guide. A perfect way to open up floor space in a compact bedroom while adding a chic, practical touch.

A primary objective for our Modern Farmhouse Boho bedroom transformation was solving the end table dilemma.

We were fed up with the current state of our limited space:

Bedroom with a dresser beside one side and a table and chair on the other.
The mismatched end table setup appeared cluttered and overwhelming in our petite room.

Following our small closet organization project and applying a striking black feature wall, we felt set to construct some straightforward DIY floating end tables.

And, by "we", I refer to my spouse.;) He fashioned these swift and easy bedroom furnishings while I focused on painting and organizing the closet.

I merely stepped in to capture a few images and express delight at the opportune moments, but honestly, this was entirely his vision, and I am truly enchanted by the results!

If you are also searching for a straightforward and affordable floating beside table concept, this could be the resolution to your problems.

How to Build DIY Floating Bedside Tables in Just a Few Hours

Crafting DIY Floating Bedside Companions

Disclaimer: This entry features affiliate links for your shopping ease.

Essentials Required for these Floating Bedside Tables:

  • Two – 1×6 inch tongue and groove pine planks eight feet in length (which yields two floating nightstands)
  • Wood Adhesive
  • Brad Nailer (my husband’s model is a generic brand, yet this remains his coveted tool.)
  • Compound Miter Saw (comparable)
  • MDF panel for the rear section
  • Clamps
  • Screws and a screwdriver
  • Stud Finder
  • Wall Anchors

Fasten and adhere the tongue and groove planks that will form the "casing" of the floating table.

Wood pieces cut in preparation for making floating bedside tables

Each floating end table "casing" is comprised of the following components:

Four segments cut to 22 inches (featuring a 45-degree angle at each extremity – as depicted above)

Four segments cut to 8 inches (with 45-degree angles at each extremity – as depicted above)

Begin by joining the side sections to the base of the nightstand.

Glue being squeezed onto the edges that need to join together for DIY floating bedside tables

Secure these components using an air nailer.

A brad nailer being used to secure the joints of a floating bedside table

Apply the identical procedure to complete the opposing side of the table.

Next, affix the top piece to the nightstand structure with adhesive and an air nail gun.

Glue being squeezed on to the corners of the wood where the top of bedside table will be attached.

Affix the mdf backing to the rear of the shelf using glue and air gun brads.

The back piece of wood being attached to the back of a floating bedside table with a brad nailer.

Smooth the entire surface thoroughly with sandpaper, then apply your preferred stain or paint color.

Our selection was the Early American Stain by Minwax. Keep in mind that MDF absorbs stain differently than pine wood; however, the stain gave the back a pleasing suede-like texture.

Alternatively, for a floating nightstand finish, you could paint or cover the back panel with wallpaper in a contrasting hue.

Instructions for mounting a floating nightstand onto a wall follow.

After the nightstand is fully finished, the next task is mounting it on the wall. Here is the method:

  • Locate wall studs with a stud finder, then lightly mark the positions using a pencil or painter's tape. It is highly suggested that at least one side of the stand be fastened securely to a wall stud if possible.
  • Decide on the desired height for the nightstand; ours was set to align with the top of our mattress.
  • Should two studs not be found for mounting, pinpoint the intended location for the second set of screws.
  • Utilize a level to ensure the nightstand remains perfectly horizontal.
  • Fasten the nightstand to the studs employing screws and a drill driver.
  • Using a drill, mark the placement for the second screw set, then drill a small pilot hole through the nightstand and into the wall to guide the drywall anchors.
  • Detach the nightstand and position the drywall anchors.
  • Reattach the nightstand to the studs, then secure the drywall anchors with screws.
Finished floating bedside table attached to the wall with 4 screws.

Screw plugs can be used to conceal the screws if desired, though most people won't inspect the rear of their floating nightstand closely!

The floating bedside table completed and hung on the wall beside a bed with a plant on the top and books in the shelf.

We found the construction remarkably straightforward and these pieces perform excellently!

2 DIY floating bedside tables flanking a bed

Expenditure for these DIY Floating Endtables:

  • Two 8-foot tongue and groove pine boards (sufficient for both end tables) cost $20.

All supplementary materials were already available in our possession.

The One Room Challenge, Week 5 was postponed because of global happenings

This post is part of the One Room Challenge makeover series hosted by Calling it Home and Better Homes and Gardens. If you’d like to catch up on the previous posts, here they are:

How to Build DIY Floating Bedside Tables in Just a Few Hours

To see how all the other rooms are coming along, head on over to the One Room Challenge site next week and check out all the progress.